BSI-102 Insta-Cure Super Thin Glue

Features And Benefits:

Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.

Share (1)
Total: 1 Total: 0
SKU: BSI102 Category:

Description

Description:

Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.

Directions:

Unscrew top from nozzle. For finer applications, use the extender tip. Insta-Cure™ CA is used to bond tight fitting parts. Hold the parts together (sometimes using masking tape), then apply the Insta-Cure™ along the joints. The CA will penetrate deep into the joints. Bonding will occur in 1-3 seconds. Excess cured CA can be removed from surfaces like ceramics by rubbing with a paper towel soaked in Un-Cure™. Full strength is reached in two hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220º F. Soak extender tip in acetone for cleaning.

 

Additional information

Manufacturer

Bob Smith Industries
P/N:

BSI-102
M/N:

Insta-Cure Super Thin
Size

1 oz. Bottle

Reviews

There are no reviews yet.

Be the first to review “BSI-102 Insta-Cure Super Thin Glue”

Related products

  • Glue & Adhesives

    BSI-107 Insta-Cure + Gap Filling Medium Glue

    Features And Benefits:

    Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1″ separations on one surface, then assemble the parts, letting the pressure spread the CA out.

    (0 reviews)
    Read more
  • Glue & Adhesives

    BSI-161 Un-Cure Debonder CA Remover

    Features And Benefits:

    UN-CURE™ Debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. Since cured CA is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using Un-Cure on plastics. Separating plastics parts with a razor saw is usually the best option.

    (0 reviews)
    $3.29 Add to cart
  • Glue & Adhesives

    BSI-201 Quik-Cure Epoxy

    Features And Benefits:

    QUIK-CURE™ 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE™ shouldn’t be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. QUIKCURE™ is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CURE™ can be handled after 15 minutes. Full strength is reached in 1 hour.

    (0 reviews)
    Read more